| 以文本方式查看主題 - 曙海教育集團論壇 (http://www.mikehunterok.com/bbs/index.asp) -- Linux應用開發 (http://www.mikehunterok.com/bbs/list.asp?boardid=32) ---- 如何解決Linux操作系統找不到網卡的問題 (http://www.mikehunterok.com/bbs/dispbbs.asp?boardid=32&id=1664) |
| -- 作者：wangxinxin -- 發布時間：2010-11-23 10:46:44 -- 如何解決Linux操作系統找不到網卡的問題 1. 安裝網卡 機器太新，以至于現有的Linux版本無法認出，比如機器找不到網卡，這時候怎么辦呢？ 別急，首先你需要知道網卡是什么型號的，以本實驗室新購入的電腦為例，它的網卡是集成的，型號是Realtek RTL8168/8111 PCI-E Gigabit Ethernet NIC。然后我們到Realtek的官方網站去下載相應的Linux驅動程序r8168-8.005.00.tar.bz2，按照說明安裝。 Unpack the tarball : # tar vjxf r8168-8.aaa.bb.tar.bz2 Change to the directory: # cd r8168-8.aaa.bb If you are running the target kernel, then you should be able to do : # make clean modules (as root or with sudo) # make install # /sbin/depmod -a # /sbin/insmod ./src/r8168.ko (or r8168.o in linux kernel 2.4.x) You can check whether the driver is loaded by using following commands. # /sbin/lsmod | grep r8168(看看有沒有加載網卡驅動) # /sbin/ifconfig –a(看看有沒有相關網卡被啟動的信息) If there is a device name, ethX, shown on the monitor, the linux driver is loaded. Then, you can use the following command to activate the ethX. # ifconfig ethX up ,where X=0,1,2,... 這里也可以通過系統→管理→網絡來設置IP地址等，最后激活。 1. Set manually a. Set the IP address of your machine. # ifconfig ethX "the IP address of your machine" b. Set the IP address of DNS. Insert the following configuration in /etc/resolv.conf. nameserver "the IP address of DNS" c. Set the IP address of gateway. # route add default gw "the IP address of gateway" 2. Set by doing configurations in /etc/sysconfig/network-scripts /ifcfg-ethX for Redhat and Fedora, or /etc/sysconfig/network /ifcfg-ethX for SuSE. There are two examples to set network configurations. a. Fix IP address: DEVICE=eth0 BOOTPROTO=static ONBOOT=yes TYPE=ethernet NETMASK=255.255.255.0 IPADDR=192.168.1.1 GATEWAY=192.168.1.254 BROADCAST=192.168.1.255 2. 修改：＃vi /etc/hosts，在該文本中，增加兩行： 127.0.0.1 localhost.localdomain localhost 192.168.4.101 node3（根據機器本身情況設置） 修改：vi /etc/hosts.equiv，增加一行：(如果沒有該文本，可建立一個) node3 3. 啟動ssh服務 大部分的Linux版本應該都會自帶該程序 ＃ssh-keygen ＃cd .ssh ＃cp id_rsa.pub authorized_keys ＃ssh node3（如果成功，會顯示上次登陸的時間， node3是主機名） 附加信息： ifup eth0看看能否啟動eth0 lsmod看看有沒有加載網卡驅動 dmesg看看有沒有網卡啟動時的錯誤信息 |